A flanged joint is only as reliable as the bolting that holds it together. Rajdeep Metals supplies stud bolts, hex bolts, nuts and washers to ASTM / ASME bolting specifications, matched in grade and class to the flange, gasket and service temperature of your system.
We supply complete bolt-and-nut sets — for example A193 B7 studs with A194 2H heavy hex nuts, or A320 L7 studs with A194 Gr. 7 nuts for low-temperature service — with heat-number traceability and test certificates for every lot.
| Bolting (High Temp.) | ASTM A193 / ASME SA193 Gr. B7, B7M, B16, B8 / B8M (Class 1 & Class 2) |
|---|---|
| Nuts | ASTM A194 / ASME SA194 Gr. 2H, 2HM, 4, 7, 8, 8M |
| Bolting (Low Temp.) | ASTM A320 / ASME SA320 Gr. L7, L43, B8 (Class 1 & 2) |
| High-Temp. Superalloy | ASTM A453 Gr. 660 (A-286, Class A / B / C / D) |
| Structural & General | ASTM A307 Gr. A / B, ASTM F3125 Gr. A325 & A490 (heavy hex structural bolts) |
| Stainless Steel | ASTM F593 (bolts, screws, studs), ASTM F594 (nuts) — Alloy Group 1 (304) & Group 2 (316) |
| Nickel Alloys | ASTM B160 (Nickel 200/201), B164 (Monel 400 / R-405), B166 (Inconel 600), B574 (Hastelloy C276) bar for fasteners |
| Dimension Standards | ASME B18.2.1 (bolts), ASME B18.2.2 (nuts), ASME B18.31.2 (stud bolts), DIN 931 / 933 / 934 / 125 / 127, ISO 4014 / 4017 / 4032 |
| Size Range | Metric M6 – M72 | Imperial 1/4" – 4" (larger sizes to order) |
| Length | Standard lengths and cut lengths to ASME B16.5 / B16.47 flange stud-bolt charts, or as per drawing |
| Thread | UNC, UNF, 8-UN, BSW, BSF, Metric Coarse & Fine (ISO 261) — Class 2A / 2B, 6g / 6H |
| Coating / Finish | Plain, Black Oxide, Zinc Plated, Hot-Dip Galvanised, Xylan / PTFE Coated, Cadmium (on request) |
| Testing | Tensile, Proof Load, Hardness, Charpy Impact (A320), PMI, Thread Gauging, Dimensional Inspection |
Quenched & tempered Cr-Mo bolting (B7, B16, L7) for high-pressure flanged joints.
ExploreB8 / B8M and duplex fasteners for corrosive, marine and cryogenic service.
ExploreMonel, Inconel and Hastelloy bolting for seawater, acids and extreme heat.
ExploreA307 and structural bolts for general fabrication, steel structures and foundations.
Explore| Grade | C | Mn | Si | P | S | Cr | Ni | Mo | Other |
|---|---|---|---|---|---|---|---|---|---|
| B7 / B7M (AISI 4140) | 0.37 – 0.49 | 0.65 – 1.10 | 0.15 – 0.35 | 0.035 | 0.040 | 0.75 – 1.20 | — | 0.15 – 0.25 | — |
| B16 | 0.36 – 0.47 | 0.45 – 0.70 | 0.15 – 0.35 | 0.035 | 0.040 | 0.80 – 1.15 | — | 0.50 – 0.65 | V 0.25 – 0.35 |
| L7 (AISI 4140) | 0.37 – 0.49 | 0.65 – 1.10 | 0.15 – 0.35 | 0.035 | 0.040 | 0.75 – 1.20 | — | 0.15 – 0.25 | — |
| B8 (304) | 0.08 | 2.00 | 1.00 | 0.045 | 0.030 | 18.0 – 20.0 | 8.0 – 11.0 | — | — |
| B8M (316) | 0.08 | 2.00 | 1.00 | 0.045 | 0.030 | 16.0 – 18.0 | 10.0 – 14.0 | 2.00 – 3.00 | — |
Chemistry of nut grades (A194) and nickel alloy fasteners follows the respective product specification; heat-wise values are reported on the mill test certificate.
| Grade | Tensile Strength (MPa / ksi) | Yield Strength 0.2% (MPa / ksi) | Elongation (%) | Hardness |
|---|---|---|---|---|
| A193 B7 | 860 / 125 | 720 / 105 | 16 | 321 HB max |
| A193 B7M | 690 / 100 | 550 / 80 | 18 | 235 HB max |
| A193 B16 | 860 / 125 | 725 / 105 | 18 | 321 HB max |
| A193 B8 Class 1 | 515 / 75 | 205 / 30 | 30 | 223 HB max |
| A193 B8M Class 1 | 515 / 75 | 205 / 30 | 30 | 223 HB max |
| A320 L7 | 860 / 125 | 725 / 105 | 16 | 321 HB max |
| A194 2H (nut) | Proof stress 175 ksi (1210 MPa) | 248 – 327 HB | ||
Strength requirements for B7, B16 and L7 reduce for diameters above 2-1/2". A320 L7 is additionally impact tested at −101 °C (−150 °F).
| Nominal Size | Width Across Flats (in) | Width Across Flats (mm) | Thickness (in) | Thickness (mm) |
|---|---|---|---|---|
| 1/2" | 7/8 | 22.2 | 31/64 | 12.3 |
| 5/8" | 1-1/16 | 27.0 | 39/64 | 15.5 |
| 3/4" | 1-1/4 | 31.8 | 47/64 | 18.7 |
| 7/8" | 1-7/16 | 36.5 | 55/64 | 21.8 |
| 1" | 1-5/8 | 41.3 | 63/64 | 25.0 |
| 1-1/8" | 1-13/16 | 46.0 | 1-7/64 | 28.2 |
| 1-1/4" | 2 | 50.8 | 1-7/32 | 31.0 |
| 1-1/2" | 2-3/8 | 60.3 | 1-15/32 | 37.3 |
| Thread Size | Width Across Flats (mm) | Head Height (mm) |
|---|---|---|
| M6 | 10 | 4.0 |
| M8 | 13 | 5.3 |
| M10 | 16 | 6.4 |
| M12 | 18 | 7.5 |
| M16 | 24 | 10.0 |
| M20 | 30 | 12.5 |
| M24 | 36 | 15.0 |
| M30 | 46 | 18.7 |
Nominal (basic) dimensions shown. Stud bolt lengths for flanged joints follow ASME B18.31.2 and the bolting tables of ASME B16.5 / B16.47. See Technical Data for more charts.
Send your flange list or stud-bolt schedule — we will quote matched bolts, nuts and washers.